Traduction automatique (Description - Fabricant): Combiné avant/arrière vue remplace curiosités question d'une Auto 1911 avec un minimum de tracas. Lame surplombe l'arrière de la lame pendant le ramassage rapide. Plus...
Combiné avant/arrière vue remplace curiosités question d'une Auto 1911 avec un minimum de tracas. Lame surplombe l'arrière de la lame pendant le ramassage rapide. Coins et les bords sont arrondis. Se monte dans l'usine en queue d'aronde.
Plus...
Front/rear sight combo replaces a 1911 Auto's issue sights with a minimum of hassle. Blade overhangs the back of the slide for fast pick-up. Corners and edges are rounded. Mounts in factory dovetail.
Plus...
Évaluations client de MGW 1911 Auto Fixed Sight Combos, IRS/WD/NT
Nombre d'évaluations: 13
De brownells.com: 13
Note moyenne: 4,5
improvement over Gi sights.(07/01/2011)
Used on a rock island 1911A1 GI, which i found out too late is a narrow tenon, not MGW's fault. However, the hang down on the backing on the rear sight (you can see in the pic below the 2 white does how it hangs down like a tail) will not fit on a GI 1911. It was easliy filed though, jsut not sure if it is supposed to hang down over the back of the slide or what. the Angle of the dove tail was not the same as my RIA, but also easily fixed with a file. Overall average product. mass improvement over standard gi sights, little dissapointment with the amount of filing required to give it 4 or 5 stars.
Very Good Affordable Sights(18/10/2014)
I purchased a Springfield 1911 a few weeks ago from a local gun show. This is my first hand gun I have owned, and when I went shooting at the range for the first time, I noticed the sights were very difficult to see and line up correctly, so I purchased these MGW sights for two reasons. One, they were much easier to see, and two, the price. Now the installation was done by a local gunsmith, and because of the milling needed on the front sight, the price to install was a little spendy, under $100, but still worth the money to have sights that you can actually use. I am very happy with them, and the gun fits in my Fobus holster just fine with new sights.
Excellent Sight Set!(18/05/2018)
I installed this sight set on an ATI 1911-A1 Military Model. The pistol in the rough (is a gem in the rough) came with the standard GI sights. The factory sights were dead on but take critical time to acquire due to their small size. I installed these MGW sights. I had no issue staking in the front. The rear needed a small amount of filing, however were soon a perfect fit.
Here is the important part. I was taking head shots at a B27 silhouette first at 15, then 25, then 35 yards at center mass. No misses. These sights have a 1970âs look to them, Wich I do like, and acquire rapidly, and shoot PERFECTLY.
Looks nice(17/04/2010)
I had to aggressively file the rear sight dovetail to get it to engage the slot on my Springfield GI. Looks nice once it is on.
Great Sight(02/06/2011)
Excellent sight for the price. Straight forward easy instillation. Looks great on my Rock Island A-1. Be gentle with the finish mine rubbed away while installing with a sight instillation jig. This could have easily been avoided with a buffer between the sight and the driving pin.
Sight is great.(01/01/2012)
Mounted the sights on a Colt Series 70 Lightweight Commander without any modifications needed to rear dovetail. Front staked in without any problems as well with narrow tenon. The dots are great. The sights were cerekoted to match gun during rebuild. Gun shots to point of aim with minor drifting of rear sight.
Great sights!(14/03/2012)
Ordered on Saturday, got them on Wednesday, installed them that afternoon. Only took minor fitting for the front sight and the back sight tapped right in to my plain-Jane Auto Ordnance M1911A1 Govt.
Get the front sight post staking tool too. it's worth every penny!
easy to mount for a first timer(26/12/2012)
I added these to my 1911A1 Norinco, I had to file the rear sight a bit to get it to fit the dove tail on my slide. the front sight needed to be filed down slightly to fit the milled flat section of the slide where the front sight rests. This was the first time I tried this,so with set up and everything it took me 11/2 hours to complete but it turned out perfect. I used a sight staking tool for the front tenon.
Most usable sight I've ever had(09/02/2013)
I purchased these to replace the GI sights on my 1911. After a little fitting, I was very pleased with the result. Having the rear sight blade at the back of the slide rely draws your eyes to the sights. The wide rear notch allows plenty of light around the front sight blade providing a very usable sight picture. I'd recommend these for anyone looking for a quality sight set, be it just for plinking or on your everyday carry gun.
Great GI upgrade...(22/05/2013)
Very happy with upgrade on Kahr Auto-Ordnance "WWII Parkerized" 1911PKZSE.
Kahr Auto-Ordnance WWII 1911PKZSE(13/06/2013)
A perfect upgrade on my Kahr Auto-Ordnance "WWII Parkerized" 1911PKZSE gun. Much better than the stock GI sights, and still looks good on the gun.
Nice looking sights(29/06/2013)
I installed this set on my RIA .45, needless to say I had to filse the cut on the pistol to force this to fit,I used a hammer and drift punch, it did mar the finish but a little flat touch up will make it look as good as new. It looks grat and it works great. Any issues I have had are due to nevef installing a front or rear sight before but came out well.
Needed modifications.(05/03/2015)
I bought these sights to up grade my project gun. The slide tenon was too far forward for the rear of the sight to clear the slide. I had to file the bottom of the rear sight face to make it work.
The quality and value cannot be beat, it just did not fit my application without modification.
584003645 MGW 1911 Auto Fixed Sight Combos, IRS/WD/NT Ref Fabricant: MGW2031 Combiné avant/arrière vue remplace curiosités question d'une Auto 1911 avec un minimum de tracas. Lame surplombe l'arrière de la lame pendant le ramassage rapide. Coins et les bords sont arrondis. Se monte dans l'usine en queue d'aronde.
54.49EUR754,49 €
*
En stock
Caractéristiques:Couleur de Visée: BlancManufacture: 1911Modèle: Government, Commander, OfficersStyle: Point, Rampe, Broche Etroite, Point Blanc
584003745 MGW 1911 Auto Fixed Sight Combos, IRS/WD/WT Ref Fabricant: MGW2032 Combiné avant/arrière vue remplace curiosités question d'une Auto 1911 avec un minimum de tracas. Lame surplombe l'arrière de la lame pendant le ramassage rapide. Coins et les bords sont arrondis. Se monte dans l'usine en queue d'aronde.
54.49EUR354,49 €
*
En stock
Caractéristiques:Couleur de Visée: BlancManufacture: 1911Modèle: Government, Commander, OfficersStyle: 3-Point, Rampe, Encoche Tenon, Point Blanc
Combiné avant/arrière vue remplace curiosités question d'une Auto 1911 avec un minimum de tracas. Lame surplombe l'arrière de la lame pendant le ramassage rapide. Coins et les bords sont arrondis. Se monte dans l'usine en queue d'aronde.
Plus...
Front/rear sight combo replaces a 1911 Auto's issue sights with a minimum of hassle. Blade overhangs the back of the slide for fast pick-up. Corners and edges are rounded. Mounts in factory dovetail.
Plus...
Évaluations client de MGW 1911 Auto Fixed Sight Combos, IRS/WD/NT
Nombre d'évaluations: 13
De brownells.com: 13
Note moyenne: 4,5
improvement over Gi sights.(07/01/2011)
Used on a rock island 1911A1 GI, which i found out too late is a narrow tenon, not MGW's fault. However, the hang down on the backing on the rear sight (you can see in the pic below the 2 white does how it hangs down like a tail) will not fit on a GI 1911. It was easliy filed though, jsut not sure if it is supposed to hang down over the back of the slide or what. the Angle of the dove tail was not the same as my RIA, but also easily fixed with a file. Overall average product. mass improvement over standard gi sights, little dissapointment with the amount of filing required to give it 4 or 5 stars.
Very Good Affordable Sights(18/10/2014)
I purchased a Springfield 1911 a few weeks ago from a local gun show. This is my first hand gun I have owned, and when I went shooting at the range for the first time, I noticed the sights were very difficult to see and line up correctly, so I purchased these MGW sights for two reasons. One, they were much easier to see, and two, the price. Now the installation was done by a local gunsmith, and because of the milling needed on the front sight, the price to install was a little spendy, under $100, but still worth the money to have sights that you can actually use. I am very happy with them, and the gun fits in my Fobus holster just fine with new sights.
Excellent Sight Set!(18/05/2018)
I installed this sight set on an ATI 1911-A1 Military Model. The pistol in the rough (is a gem in the rough) came with the standard GI sights. The factory sights were dead on but take critical time to acquire due to their small size. I installed these MGW sights. I had no issue staking in the front. The rear needed a small amount of filing, however were soon a perfect fit.
Here is the important part. I was taking head shots at a B27 silhouette first at 15, then 25, then 35 yards at center mass. No misses. These sights have a 1970âs look to them, Wich I do like, and acquire rapidly, and shoot PERFECTLY.
Looks nice(17/04/2010)
I had to aggressively file the rear sight dovetail to get it to engage the slot on my Springfield GI. Looks nice once it is on.
Great Sight(02/06/2011)
Excellent sight for the price. Straight forward easy instillation. Looks great on my Rock Island A-1. Be gentle with the finish mine rubbed away while installing with a sight instillation jig. This could have easily been avoided with a buffer between the sight and the driving pin.
Sight is great.(01/01/2012)
Mounted the sights on a Colt Series 70 Lightweight Commander without any modifications needed to rear dovetail. Front staked in without any problems as well with narrow tenon. The dots are great. The sights were cerekoted to match gun during rebuild. Gun shots to point of aim with minor drifting of rear sight.
Great sights!(14/03/2012)
Ordered on Saturday, got them on Wednesday, installed them that afternoon. Only took minor fitting for the front sight and the back sight tapped right in to my plain-Jane Auto Ordnance M1911A1 Govt.
Get the front sight post staking tool too. it's worth every penny!
easy to mount for a first timer(26/12/2012)
I added these to my 1911A1 Norinco, I had to file the rear sight a bit to get it to fit the dove tail on my slide. the front sight needed to be filed down slightly to fit the milled flat section of the slide where the front sight rests. This was the first time I tried this,so with set up and everything it took me 11/2 hours to complete but it turned out perfect. I used a sight staking tool for the front tenon.
Most usable sight I've ever had(09/02/2013)
I purchased these to replace the GI sights on my 1911. After a little fitting, I was very pleased with the result. Having the rear sight blade at the back of the slide rely draws your eyes to the sights. The wide rear notch allows plenty of light around the front sight blade providing a very usable sight picture. I'd recommend these for anyone looking for a quality sight set, be it just for plinking or on your everyday carry gun.
Great GI upgrade...(22/05/2013)
Very happy with upgrade on Kahr Auto-Ordnance "WWII Parkerized" 1911PKZSE.
Kahr Auto-Ordnance WWII 1911PKZSE(13/06/2013)
A perfect upgrade on my Kahr Auto-Ordnance "WWII Parkerized" 1911PKZSE gun. Much better than the stock GI sights, and still looks good on the gun.
Nice looking sights(29/06/2013)
I installed this set on my RIA .45, needless to say I had to filse the cut on the pistol to force this to fit,I used a hammer and drift punch, it did mar the finish but a little flat touch up will make it look as good as new. It looks grat and it works great. Any issues I have had are due to nevef installing a front or rear sight before but came out well.
Needed modifications.(05/03/2015)
I bought these sights to up grade my project gun. The slide tenon was too far forward for the rear of the sight to clear the slide. I had to file the bottom of the rear sight face to make it work.
The quality and value cannot be beat, it just did not fit my application without modification.
Si vous aimez tirer, travailler sur les armes en tant que professionnel ou pour votre loisir, ou bien simplement posséder une arme à feu, brownells.fr est fait pour vous!
Depuis plus de 75 ans, tireurs, armuriers professionnels, amateurs, militaires / armuriers des forces de l'ordre ou encore as du bricolage d'armes à feu se sont tournés vers brownells.fr pour s'approvisionner en pièces et fournitures de haute qualité dont ils ont besoin.
Vous trouverez plus de 90.000 produits, y compris des pièces détachées uniques d'armes à feu, des accessoires, des outils d'armuriers, des munitions et bien d'autres produits pour entretenir, réparer et mettre à niveau vos armes.
Nous vous garantissons votre satisfaction à 100% -Toujours!