Caractéristiques
- Couleur: Noir
- Matériau: Fiberglass
- Modèle: 10/22
- Type d'arme: Ruger
- Poids du colis: 1,111kg
- Hauteur d'expédition: 64mm
- Largeur d'expédition: 178mm
- Longueur d'expédition: 889mm
- UPC: 743108220108
Détails de l'article

Le prix inclut la TVA mais pas la livraison .
Référence: 408220100
N° fabr.: 22010
743108220108 Peau extérieure en caoutchouc ou en nylon rembourrée moulée sur une coque en fibre de verre. La peau extérieure en caoutchouc rembourrée offre un confort de tir antidérapant ; le corps en fibre de verre interne fournit un support solide, est léger et facile à transporter. Entièrement usinée pour un ajustement parfait ; modèles disponibles pour s'adapter aux canons bull de diamètre nominal de .920" (B/B). Crosse droite ; avant large de style varmint avec rainures pour les doigts, finition en pavé sur la prise et l'avant ; doubles renflements de paume et poignée de pistolet recourbée rendent cette crosse aussi confortable à tirer qu'elle est pratique. Comprend un pad de recul en caoutchouc et des œillets de sangle avant et arrière.La crosse RUGER 10/22 avec revêtement en caoutchouc est conçue pour offrir un confort de tir exceptionnel tout en étant légère et facile à transporter.
Avec cette crosse, tu seras prêt à tirer avec précision et confort. Ne manque pas cette opportunité d'améliorer ton équipement !
All around great stock 07/04/2018
Bought this to fit my new Mist 22 integral barrel/silencer and to give the gun a more modern look. There was a little fitting needed because the barrel was a little over .925 in diameter but just scraped it of with a sharp knife in about a minute and it fit fine. It feels great during shooting and just all around looks great, hard to beat the price too.
Great Stock One Fore End Caveat 27/07/2013
Built a 10/22 using:
Timney 10/22 Drop-In Trigger Assembly 883-000-038WB -- great trigger assembly, drop in with no fitting required. The lever magazine release is a great addition, helping with making the rifle a little more ambidextrous. The spring loaded bolt release works as we are accustomed to unlike the factory release. The trigger pull is crisp and clean reminiscent of the Jewel triggers on my 700. The trigger is a vast improvement over factory. 4 stars as the pull measured 3lbs on my Lyman gauge, preferred for hunting but as it is not adjustable I don't consider this a bench rest trigger.
ER Shaw Fluted 10/22 .920 Target Barrel, SS 100-004-747WB -- everything I was looking for. Looks great and shoots great. 1/2" groups at 75 yards on a 100 degree, 10 - 15 mph gusty day with 20 year old Remington Golden Bullet HP, very satisfying. The barrel dropped right into the action and was installed using the factory V-block without barrel droop. V-block barrel retaining screws screws were just snugged. Checked with a set of headspace gauges and everything was fine and good to go. A 5 star barrel for sure.
Hogue 10/22 Overmolded Rifle Stock B/B Rubber Covering 408-220-100WB -- The stock I wanted was out of stock so I got this one to do the build. I am liking it. Feels good in hand and on the shoulder. Ambidextrous! Bedding was accurate and felt solid. With the action screw torqued to 18 in-lbs the Shaw barrel was dollar bill free floated from 1" behind the flutes to the muzzle. The semi-varmint fore end is a joy in hand or on a bag. 4 Stars as the fore end will flex enough to touch the barrel with moderate straight line side hand pressure, a hasty sling or tight sling. Still I may well forget about the stock I wanted that cost 2-1/2 times as much, this one shoots and feels so good.
Volquartsen 10/22 Socket Head Takedown Screw 930-000-O26WB -- Comparing this screw to my factory screw it is about 2-1/2 threads shorter. However it fit this build just fine, earning it 5 Stars. It and the receiver handled 18 in-lbs of torque without problem.
Nous avons rencontré une erreur lors du chargement de ce contenu. Veuillez actualiser la page pour continuer. Si le problème persiste, contactez notre service client.