Votre panier est vide.

Panier

YANKEE HILL MACHINE CO., INC.
FOREARM WRENCH

100002090

Cette clé à ergot robuste en acier facilite le serrage des écrous de canon de garde-main au couple correct. L'extrémité encochée s'engage dans la bague d'indexation des garde-mains Yankee Hill et d'autres modèles similaires avec des bagues d'indexation à fentes, permettant ainsi d'aligner les rails d'accessoires.

SPECS: Acier, finition oxyde noir. Longueur 8" (20.3cm), largeur 2" (5.1cm), épaisseur ¼" (6.4mm).

Plus...

Heavy, steel, spanner wrench makes it easy to tighten handguard barrel nuts to the correct torque. Notched end engages the indexing ring on Yankee Hill handguards and others with similar, slotted indexing rings for aligning the accessory rails.

SPECS: Steel, black oxide finish. 8" (20.3cm) long, 2" (5.1cm) wide, ¼" (6.4mm) thick.

Plus...

Évaluations client de YANKEE HILL MACHINE CO., INC. FOREARM WRENCH

Nombre d'évaluations: 12
De brownells.com: 12
Note moyenne: 3,2

Not enough leverage! (26/03/2010)

No hole for breaker bar or torque wrench. Could not get some nuts off with this wrench. a Standard armorers wrench works just fine.

Works great! (29/06/2010)

It's an INSTALLATION TOOL, not a breaker bar to remove barrel nuts installed by some ham-fisted moron with Locktite. Also, it's a MUST for the jamb nut installation.

might be needed (01/07/2010)

a previous comment was that a good armorer's tool will do anything required of this 'forearm wrench'. i almost believed that comment, but i bought the wrench anyway and was mad at myself for doing so(because i have so many tools)until i went to tighten everything down. i found this wrench to be very important to me.

Fragile Junk (08/09/2010)

I barely gave this wrench a stern look and one of the pins sheared clean off. It's a piece of junk. You're better off using a standard USGI wrench or one of the encapsulating-style ones from Smith or DPMS.

Excellent for the job! (19/09/2010)

I had previously mounted a YHM FreeFloat Tube with only a strap wrench and it took forever. I bought this and it is perfect for the job!

Necessary, costs too much (03/12/2010)

This tool works perfectly if you follow the directions and use it for what it was intended. It is NOT intended to take old barrel nuts off - you need an armorer's wrench for that.

There is no way to measure torque with this wrench. YHM recommends that hand-tighten their barrel nut and then turn to the next available hole for the gas tube. If you prefer to verify a min. 35 ft# you need an armorer's wrench that allows for the attachment of a torque wrench.

This tool has one function - it is to engage the recesses in the locking collar to snug it tight. You can make other tools work, but this is the only one that works properly.

For it's very limited function it costs too much, but as with the the special wrenches for, e.g. the Daniel Defense rails (which wrenches also cost too much for what they are), you're paying for a professional install, not for the tool itself.

NO, I would not recommend it to a friend because for the cost, I'd let him borrow mine. If you can borrow it, do that.

Garbage (22/01/2011)

Used it and broke the pegs off it before accomplishing anything. Switched over to a DPMS tool and finished the job. Buy a DPMS or other quality tool instead.

This is NOT a standard tool (15/09/2011)

As remarked by another reviewer. This is designed for Yankee Hill free floats. I gave it 4 as is it not a wrench tool for ALL AR's. Also, when tightening the jam nut. Painters tape and great care must be taken to prevent marring of the jam nut. If you do a lot of Yankee Hill free floats. This is a nice tool. As an FYI. Many free floats use their own mount tools. Only Milspec original parts take generic armorer tools. When you get in to free floats or .308 caliber. They all use their own hole pattern and custom mount design. One of the nice features of many YHM free floats is the anti rotation screw models, which ensure a solid mount system for M1913 standard rail platform.

Works great to install YHM handguards (15/01/2012)

I've installed many YHM handguards without a problem, that's the only job that I use this tool for. Some of the reviewers report using this wrench for other duties and that may be the source of their disappointment. It may be possible to scratch the lock ring if used carelessly.

Pins broke too easily (15/06/2013)

Ive had this tool for 2 years and it sees light duty. Yesterday, the pins sheared off of it completely. For the price, it should've lasted more than 15 uses.

Broke the first time (24/10/2016)

Bought this as an addition to the tool box. The very first time I used it, a pin sheared off and damaged the customers barrel nut. The tool appears to be well made, and the barrel nut was not "loc-tited" in. It simply sheared off. Although I would usually blame the manufacturers, in this case i'm betting it was a random pin defect. I love Brownells guarantees, and they make the exchange easy.

<img width="500" src='/userdocs/reviewimages/e023472b-756c-4a14-9e9c-89fa416c98fe.jpg' alt=''>

Very well made (19/11/2016)

Very well made , only way to properly tighten the lock nut. Just remember not to install gas block yet , as tool is a full circle and wont fit over the gas block . Very happy with the tool.

Lire 12 plus d'avis sur brownells.com

0 0 1 EUR

Référence: 100002090
YANKEE HILL MACHINE CO., INC. FOREARM WRENCH
Ref Fabricant: YHM9621 Cette clé à ergot robuste en acier facilite le serrage des écrous de canon de garde-main au couple correct. L'extrémité encochée s'engage dans la bague d'indexation des garde-mains Yankee Hill et d'autres modèles similaires avec des bagues d'indexation à fentes, permettant ainsi d'aligner les rails d'accessoires.

Avertir lorsque l'article est disponible

Pas disponible.

Caractéristiques: Fabrication: AR-15

Ajouter à la Liste d'Envies

Poser un question

Propriétés

Ajouter à la Liste d'Envies

Poser un question

Top takeaways

Clé à ergot robuste en acier pour serrer les écrous de canon de garde-main au couple correct.
Compatible avec les garde-mains Yankee Hill et autres modèles similaires avec des bagues d'indexation à fentes.
Spécifications : acier avec finition oxyde noir, longueur 8" (20.3cm), largeur 2" (5.1cm), épaisseur ¼" (6.4mm).

Caractéristiques

Fabrication: AR-15 Poids du colis: 0,431kg Hauteur d'expédition: 18mm Largeur d'expédition: 56mm Longueur d'expédition: 201mm

Détails de l'article

Fabriqué au USA

🔧 La clé à ergot Yankee Hill Machine Co. facilite le serrage des écrous de canon des garde-mains AR-15. Parfaite pour aligner les rails d'accessoires. En savoir plus !

SPECS: Acier, finition oxyde noir. Longueur 8" (20.3cm), largeur 2" (5.1cm), épaisseur ¼" (6.4mm).

Plus...

SPECS: Steel, black oxide finish. 8" (20.3cm) long, 2" (5.1cm) wide, ¼" (6.4mm) thick.

Plus...

Évaluations client de YANKEE HILL MACHINE CO., INC. FOREARM WRENCH

Nombre d'évaluations: 12
De brownells.com: 12
Note moyenne: 3,2

Not enough leverage! (26/03/2010)

No hole for breaker bar or torque wrench. Could not get some nuts off with this wrench. a Standard armorers wrench works just fine.

Works great! (29/06/2010)

It's an INSTALLATION TOOL, not a breaker bar to remove barrel nuts installed by some ham-fisted moron with Locktite. Also, it's a MUST for the jamb nut installation.

might be needed (01/07/2010)

Fragile Junk (08/09/2010)

Excellent for the job! (19/09/2010)

I had previously mounted a YHM FreeFloat Tube with only a strap wrench and it took forever. I bought this and it is perfect for the job!

Necessary, costs too much (03/12/2010)

Garbage (22/01/2011)

Used it and broke the pegs off it before accomplishing anything. Switched over to a DPMS tool and finished the job. Buy a DPMS or other quality tool instead.

This is NOT a standard tool (15/09/2011)

Works great to install YHM handguards (15/01/2012)

Pins broke too easily (15/06/2013)

Ive had this tool for 2 years and it sees light duty. Yesterday, the pins sheared off of it completely. For the price, it should've lasted more than 15 uses.

Broke the first time (24/10/2016)

Very well made (19/11/2016)

Very well made , only way to properly tighten the lock nut. Just remember not to install gas block yet , as tool is a full circle and wont fit over the gas block . Very happy with the tool.

Lire 12 plus d'avis sur brownells.com

Poursuivre vos achats

🚀 Donnez à votre AR-15 un look unique avec les Diamond Pattern Free Float Handguards de Yankee Hill Machine Co.! Léger, durable et parfait pour monter vos accessoires tactiques. 🌟 Découvrez plus maintenant!

YANKEE HILL MACHINE CO., INC. DIAMOND SERIES HANDGUARD, MID-LENGTH
AR-15 DIAMOND PATTERN FREE FLOAT HANDGUARDS

YANKEE HILL MACHINE CO., INC.

Non disponible

Gardes Main & Rails

4,9

MAGPUL 1.5" FLIP-UP MBUS GEN 2 FRONT SIGHT POLYMER DARK EARTH
AR-15 FLIP-UP MBUS GEN 2 FRONT SIGHT

MAGPUL

En stock

54,90 € *

Guidons

BROWNELLS AR-15/M16 LOWER RECEIVER VISE BLOCK
AR-15/M16 LOWER RECEIVER VISE BLOCK

BROWNELLS

En stock

29,90 € * 29,90 € - 69,90 €*

Etablis & Etaux

3,6

Protégez votre AR-15 avec le bouchon de garde-main Yankee Hill en aluminium noir. Installation facile, ports de refroidissement. Apprenez-en plus! 🔧💥

YANKEE HILL MACHINE CO., INC. 7/8" FOREARM END CAP ALUMINUM BLACK
AR-15 15/16" FOREARM END CAP ALUMINUM BLACK

YANKEE HILL MACHINE CO., INC.

Non disponible

Bouchons Garde-Main

4,7

TROY INDUSTRIES AR-15 GAS BLOCK LOW PROFILE .750 STEEL BLACK
AR-15 GAS BLOCK LOW PROFILE

TROY INDUSTRIES

Bientôt disponible

64,90 € *

Verrous Gaz

3,9

Connexion

Mot de passe oublié ?
S'inscrire

Notre garantie - Votre satisfaction.

Si vous aimez tirer, travailler sur les armes en tant que professionnel ou pour votre loisir, ou bien simplement posséder une arme à feu, brownells.fr est fait pour vous!
Depuis plus de 75 ans, tireurs, armuriers professionnels, amateurs, militaires / armuriers des forces de l'ordre ou encore as du bricolage d'armes à feu se sont tournés vers brownells.fr pour s'approvisionner en pièces et fournitures de haute qualité dont ils ont besoin.

Vous trouverez plus de 90.000 produits, y compris des pièces détachées uniques d'armes à feu, des accessoires, des outils d'armuriers, des munitions et bien d'autres produits pour entretenir, réparer et mettre à niveau vos armes.

Nous vous garantissons votre satisfaction à 100% -Toujours!

Votre Equipe Brownells France.

Connectez-Vous

Brownells.fr

Catégories

Commander

Service Clientèle

Notre identité

Depuis plus de 75 ans, tireurs, armuriers professionnels, amateurs, militaires / armuriers des forces de l'ordre ou encore as du bricolage d'armes à feu se sont tournés vers brownells.fr pour s'approvisionner en pièces et fournitures de haute qualité dont ils ont besoin.

Vous trouverez des pièces détachées uniques d'armes à feu, des accessoires, des outils d'armuriers, des munitions et bien d'autres produits pour entretenir, réparer et mettre à niveau vos armes.

* Le prix inclut la TVA mais pas la livraison .

Vue classique

Vue mobile