Améliore ton tir avec le montage de visée EGW pour Vortex Viper/Venom !
Le montage de visée H&K USP VORTEX VIPER/VENOM d'EGW est conçu pour te permettre d'installer facilement ta lunette rouge sur ton arme. Voici quelques détails importants :
Caractéristiques du produit :
- Les visées à point rouge EGW sont à installer de gauche à droite (avec le canon orienté vers l'avant).
- Le rail a un profil conique progressif pour faciliter l'installation.
- Remplace simplement la hausse arrière de ton arme par le montage EGW pour fixer ta lunette Vortex Viper/Venom, Burris FastFire, ou Docter.
- Tu peux retirer le montage et remettre ta hausse arrière à tout moment.
- Matériel de montage inclus.
Instructions d'installation :
- Retire la hausse arrière*
- Installe le montage de visée EGW dans le rail
- Serre la vis de réglage (si applicable)
- Place la lunette rouge sur le montage EGW (mettre un petit morceau de papier entre la lunette rouge et le montage facilitera le retrait et évitera que le Loctite ne se fixe sur la lunette).
- Applique du Loctite bleu sur les vis de montage fournies
- Serre les vis de montage à 15 in/lbs
Vis fournies :
- 2 vis à tête cylindrique - Fournies pour les lunettes Vortex Viper et Venom
- 2 vis à tête plate - Fournies pour les lunettes Burris FastFire et Docter
Les vis incluses nécessitent une clé Allen de 5/64'' pour l'installation.
Attention : La modification de ton arme peut annuler la garantie du fabricant. Ce produit doit être installé et vérifié par un armurier qualifié. Aucune responsabilité n'est exprimée ou implicite pour les dommages ou blessures pouvant résulter d'une installation ou utilisation incorrecte de ce produit.
Ce montage ne fonctionne pas avec les modèles USP Compact, USP Expert, USP Elite, VP9, VP40, P30, P30L, P30SK, HK45 ou HK45C.
EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. This mount does not work with USP Compact, USP Expert, USP Elite, VP9, VP40, P30, P30L, P30SK, HK45, or HK45C.