081950077229 Le sear en acier inoxydable trempé offre un poids de détente net de 2½ lb. La rainure du sear est rectifiée pour un angle et un engagement corrects. Comprend un ressort de retour à faible puissance et des instructions complètes.
En stock
Livraison gratuite à partir de 249,00 €.
Délai de livraison environ 14-21 jours.
Le RUGER® 77/22®, 77/17, 77/357, 77/44 et 77/50 sear & spring de TIMNEY est conçu pour réduire le poids ressenti de la détente.
Description du produit
Le sear en acier inoxydable durci offre un poids de détente net de 2½ lb. La rainure du sear est rectifiée pour assurer un angle et un engagement corrects. Ce kit comprend un ressort de retour à puissance réduite ainsi que des instructions complètes.
Hardened stainless steel sear provides a crisp 2½ lb. weight of pull. Sear notch is surface ground for correct angle and engagement. Includes reduced power return spring and complete instructions.
SPECS: Stainless steel. Fits Ruger 77/22; 77/17; 77/357; 77/44; 77/50. May require minor fitting.
Caractéristiques
Modèle:77/22
Type d'arme:Ruger
Poids du colis:0,02kg
Hauteur d'expédition:10mm
Largeur d'expédition:81mm
Longueur d'expédition:104mm
UPC:081950077229
Détails de l'article
Fabriqué au USA
US export classification: 0A501.c
Avis des clients
Notes des clients (4)
2,8 / 5
Non recommandé
posible saftey issues 29/12/2014
I installed this sear & spring in a new 77/22 wrm. It required filing the safety pad on the trigger to be able to engage the safety. Testing the trigger it broke at 2- to 2 1/4 lbs, and was crisp. The problem I encountered when closing the bolt the sear would not hold the firing pin from going forward and it would uncock the gun. If I closed the bolt very slowly, not in a normal manner it would stay cocked. This looked like a very dangerous condition. The instructions said if this happens, there is not enough tension on the sear. I took out the Timney spring and put the old factory back in . That solved the problem, but raised the trigger to 3 1/2 lbs. The photo shown would make you believe the sear is adjustable, it is not. The next time I would just buy a whole trigger assembly. I will try a Wolf aftermarket sear spring, to improve trigger pull. If this would have worked properly I would have given it 5 stars.
Moyennement recommandé
Be careful fitting it 04/06/2011
To fit this you must file the safety pad on the factory trigger. If you go too far, you can not buy a replacement trigger from Ruger, you must either send the rifle back to the factory or put in an aftermarket trigger. I put this sear in a M77/17, but it had a lot of creep. I then tried it in a M77/22, and it gave a nice 2.5 lb pull. I eventually put a Rifle Basix trigger in the M77/17 and it was MUCH easier to install and gave a better pull. I would not buy the Timney sear again and would not recommend it.
Fortement recommandé
Timney 77/22 sear only one worth using 22/05/2011
I am going to sound like a Timney fan again, but after doing trigger work on more than twelve 77/17, 77/22 and 77/22Mag rifles, I will say that the "drop in" sears from other manufacturers ALL were worthless and needed to be stoned to reduce sear engagement and to achieve a good crisp pull. I was so annoyed with these that I was using the OEM parts and stoning the nose of the sear to reduce engagement and winding up with really fine crisp single stage trigger. Then I took a chance and tried the Timney sear which I could see had a set screw to adjust sear engagement. From the factory the trigger still had a bit of creep, so I soaked the sear in WD-40 for two days to break the LocTite 271 (red) bond on the setscrew and then was able to reduce engagement a bit more and the results are just great. You DO still have to stone the safety cam to allow the cam and safety to engage properly so once you install the sear you have a modified gun which is no longer stock and can not be put back in original condition, but that is little problem. You STILL have to drill and tap the front of the trigger hanger for an overtravel screw and I use a 1/8" carbide tip drill bit to cut the rock hard receivers (the stainless as well as the carbon steel receivers are ALL very hard) and then tap 6-32 NF which results in enough thread depth to hold and then use LocTite 271 (red) to hold the setscrew permanently in place. Works just fine but BE CAREFUL in the tapping, back the tap out after cutting every new 90' turn, and use tap lubrication fluid otherwise you will break tap off in the metal trigger hanger. Frankly having to do this on a $600.00 rifle when the Remington 504 for the same money has a match fully adjustable target trigger as OEM equipment is inexcusable on the part of Ruger but the 77/22 guns are really nicely finished and many of us wish to have these in our collections. Now it is possible with a minimum amount of labor and expenditure, to end up with a target trigger pull that is diamond sharp and pulls perhaps 2.5 pounds weight. As we all know, the crispness of the release is more important than the actual weight and a heavy crisp trigger feels lower in weight than a lighter trigger that is jerky and bumpy during release. Again, buy the Timney sear!
Recommandé, avec réserves
Different from photo but works well 26/02/2010
I bought this over the Volquartsen part (which is $10 cheaper) because of the sear engagement set screw shown in the photo. The product I received doesn't have a set screw: not Brownell's fault because the Timney website shows the same picture. Regardless, I installed this on a 77/44 and it gives a much more crisp pull at just over a 2 lb break with the included spring and just over 3 lbs with the factory spring. I had to file the safety cam down a bit. Would have given it 5 stars if the photo was accurate.
Opérateur économique responsable conformément au règlement de l'UE
Brownells France
Immeuble l'Horizon 3 Rue Jacques Constant Milleret
42000 Saint-Étienne
France
contact@brownells.fr
RUGER® 77/22®; 77/17; 77/357; 77/44; 77/50 SEAR & SPRING TIMNEY RUGER® SEAR & SPRING Guide de Sécurité
Introduction
Merci d'avoir choisi le TIMNEY RUGER® SEAR & SPRING pour votre arme à feu Ruger. Ce guide fournit des instructions de sécurité essentielles et des informations pour garantir une installation et une utilisation sûres de ce produit. Veuillez lire ce guide attentivement avant de procéder.
Lignes Directrices de Sécurité Générales
Toujours manipuler les armes à feu avec soin et respect.
Assurezvous que l'arme à feu est déchargée avant d'effectuer toute installation ou maintenance.
Suivez toutes les directives du fabricant et les pratiques de sécurité lors de l'utilisation de votre arme à feu.
Rangez le sear et le ressort dans un endroit sûr et sécurisé, à l'écart des enfants et des utilisateurs non autorisés.
Vérifiez régulièrement tout signe d'usure ou de dommage sur le sear et le ressort.
Signalez tout produit dangereux ou incident aux autorités compétentes.
Précautions de Sécurité Spécifiques à l'Utilisation
Utilisez uniquement le TIMNEY RUGER® SEAR & SPRING avec les modèles Ruger spécifiés : 77/22, 77/17, 77/357, 77/44 et 77/50.
Assurezvous d'avoir les outils et les compétences nécessaires avant de tenter l'installation.
Si vous n'êtes pas sûr du processus d'installation, demandez l'aide d'un armurier qualifié.
Évitez d'utiliser une force excessive lors de l'installation pour éviter d'endommager le sear ou le ressort.
Ne modifiez pas le sear ou le ressort audelà des spécifications du fabricant.
Instructions pour l'Installation et l'Utilisation
Préparation
Assurezvous que l'arme à feu est complètement déchargée.
Rassemblez les outils nécessaires : un tournevis, des pinces et tout autre outil spécifié dans les instructions d'installation.
Retrait de l'Ancien Sear et Ressort
Suivez les instructions du fabricant pour démonter l'arme à feu en toute sécurité, si nécessaire.
Retirez soigneusement le sear et le ressort existants de l'arme à feu.
Installation du TIMNEY RUGER® SEAR & SPRING
Insérez le nouveau sear dans l'emplacement désigné, en veillant à un alignement correct.
Fixez le ressort de retour à faible puissance comme spécifié dans les instructions.
Assurezvous que la rainure du sear est correctement engagée et que l'angle est correct.
Test de l'Installation
Après l'installation, effectuez un test de fonctionnement pour garantir un fonctionnement correct.
Vérifiez le poids de la détente pour confirmer qu'il est réglé à la spécification désirée de 2½ lb.
Si nécessaire, apportez des ajustements mineurs comme indiqué dans les instructions.
Réassemblage
Réassemblez l'arme à feu selon les directives du fabricant.
Assurezvous que tous les composants sont solidement fixés et qu'il n'y a pas de pièces lâches.
Instructions de Mise au Rebut
Disposez de toutes les anciennes pièces, y compris l'ancien sear et le ressort, conformément aux réglementations locales.
Ne jetez pas les composants d'armes à feu dans les déchets ménagers ordinaires. Consultez les autorités locales pour connaître les méthodes d'élimination appropriées.
Informations de Contact pour un Support Supplémentaire
Pour toute question relative à la sécurité ou à l'installation, veuillez consulter le site Web du fabricant ou contacter leur service client. Assurezvous toujours d'avoir les dernières informations concernant la sécurité des produits et les rappels.
En suivant ces lignes directrices, vous pouvez garantir une utilisation sûre du TIMNEY RUGER® SEAR & SPRING. Merci de donner la priorité à la sécurité dans l'entretien et l'utilisation de votre arme à feu.
Nous avons rencontré une erreur lors du chargement de ce contenu. Veuillez actualiser la page pour continuer. Si le problème persiste, contactez notre service client.
Ces articles sont contrôlés par le gouvernement des États-Unis et autorisés uniquement à être exportés vers le pays de destination finale pour être utilisés par le destinataire final ou les utilisateurs finaux identifiés dans le présent document. Ils ne peuvent être ni revendus, ni cédés à tout autre pays ou toute personne autre que le destinataire final autorisé ou l'utilisateur final, soit dans leur forme originale, soit après avoir été incorporés dans d'autres produits, sans l'accord préalable du gouvernement des États-Unis ou d'une autre manière autorisée par la législation américaine, règlements.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
Ces articles sont contrôlés par le gouvernement des États-Unis et autorisés uniquement à être exportés vers le pays de destination finale pour être utilisés par le destinataire final ou les utilisateurs finaux identifiés dans le présent document. Ils ne peuvent être ni revendus, ni cédés à tout autre pays ou toute personne autre que le destinataire final autorisé ou l'utilisateur final, soit dans leur forme originale, soit après avoir été incorporés dans d'autres produits, sans l'accord préalable du gouvernement des États-Unis ou d'une autre manière autorisée par la législation américaine, règlements.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.