Pas de tour nécessaire, pas besoin de retirer le canon du cadre
Un angle super doux comme celui utilisé actuellement par Ruger sur leurs armes de poing .38/.357 DA. Si tu recules un canon Ruger ou si tu souhaites simplement reproduire cet angle sur un autre canon, utilise ce cutter. Tu NE PEUX PAS utiliser des cutters de 18° ou 11° sur un goulot de 5° sans dépasser le diamètre maximum du goulot ou créer un angle composé.
Plus...
No Lathe Needed, No Need To Remove Barrel From Frame
Super gentle angle as currently used by Ruger on their .38/.357 DA guns. If you set back a Ruger barrel or just want to duplicate this angle on any other barrel, use this cutter. You CANNOT use 18° or 11° cutters on a 5° throat without exceeding maximum throat diameter or making a compound angle.
Plus...
Évaluations client de BROWNELLS 5 CHAMFER CUTTER FOR .44-.45 CALIBER
Nombre d'évaluations: 2
De brownells.com: 2
Note moyenne: 1
My 45 cal, 5 Degree Did Not Cut.(15/05/2014)
I tried this 5 degree cutter to cut forcing cone of my 45 LC Blackhawk. Cutter chipped and dulled quickly. I returned cutter for refund. I had to clean up damage caused by 5 degree cutter using their 10 degree cutter. Forcing cone is now oversize and 10 degrees. Thank You Brownells
Failed to cut - damaged the barrel(16/11/2017)
Just as Keith Sharp said in his review, this cutter would not cut at all. It did, however, damage the barrel. I read some literature from a rental outfit that says that these are high speed steel and that this "may not" cut newer stainless steel barrels that can be ultra hard.
Brownell's needs to look into this. If the cutters are defective, find another source. If the cutters will not cut modern stainless, the ad should say that. This issue cannot be left alone.
Référence: 080486500 BROWNELLS 5 CHAMFER CUTTER FOR .44-.45 CALIBER050806009752 Un angle super doux comme celui utilisé actuellement par Ruger sur leurs armes de poing .38/.357 DA. Si tu recules un canon Ruger ou si tu souhaites simplement reproduire cet angle sur un autre canon, utilise ce cutter. Tu NE PEUX PAS utiliser des cutters de 18° ou 11° sur un goulot de 5° sans dépasser le diamètre maximum du goulot ou créer un angle composé.
Référence: 080486100 BROWNELLS 5 CHAMFER CUTTER FOR .38 CALIBER050806009707 Un angle super doux comme celui utilisé actuellement par Ruger sur leurs armes de poing .38/.357 DA. Si tu recules un canon Ruger ou si tu souhaites simplement reproduire cet angle sur un autre canon, utilise ce cutter. Tu NE PEUX PAS utiliser des cutters de 18° ou 11° sur un goulot de 5° sans dépasser le diamètre maximum du goulot ou créer un angle composé.
74.9EUR374,90 €
*
Délai de livraison environ 14-21 jours.
Caractéristiques:Calibre: 38/357 Caliber (.357-.359)Degré: 5 DegreesFabrication: Universel Arme de Poing
Pas de tour nécessaire, pas besoin de retirer le canon du cadre
Un angle super doux comme celui utilisé actuellement par Ruger sur leurs armes de poing .38/.357 DA. Si tu recules un canon Ruger ou si tu souhaites simplement reproduire cet angle sur un autre canon, utilise ce cutter. Tu NE PEUX PAS utiliser des cutters de 18° ou 11° sur un goulot de 5° sans dépasser le diamètre maximum du goulot ou créer un angle composé.
Plus...
No Lathe Needed, No Need To Remove Barrel From Frame
Super gentle angle as currently used by Ruger on their .38/.357 DA guns. If you set back a Ruger barrel or just want to duplicate this angle on any other barrel, use this cutter. You CANNOT use 18° or 11° cutters on a 5° throat without exceeding maximum throat diameter or making a compound angle.
Plus...
Évaluations client de BROWNELLS 5 CHAMFER CUTTER FOR .44-.45 CALIBER
Nombre d'évaluations: 2
De brownells.com: 2
Note moyenne: 1
My 45 cal, 5 Degree Did Not Cut.(15/05/2014)
I tried this 5 degree cutter to cut forcing cone of my 45 LC Blackhawk. Cutter chipped and dulled quickly. I returned cutter for refund. I had to clean up damage caused by 5 degree cutter using their 10 degree cutter. Forcing cone is now oversize and 10 degrees. Thank You Brownells
Failed to cut - damaged the barrel(16/11/2017)
Just as Keith Sharp said in his review, this cutter would not cut at all. It did, however, damage the barrel. I read some literature from a rental outfit that says that these are high speed steel and that this "may not" cut newer stainless steel barrels that can be ultra hard.
Brownell's needs to look into this. If the cutters are defective, find another source. If the cutters will not cut modern stainless, the ad should say that. This issue cannot be left alone.