Améliore ton tir avec le montage de viseur LPA SIGHT VORTEX VIPER/VENOM !
Le montage de viseur LPA pour les modèles Vortex Viper et Venom est conçu pour être installé facilement sur ton arme. Voici tout ce que tu dois savoir :
Description du produit
Les viseurs point rouges EGW sont conçus pour être installés de gauche à droite (avec le canon orienté vers l'avant). La queue d'aronde a un taper progressif pour faciliter l'installation. Il te suffit de retirer le viseur arrière de ton arme et de le remplacer par le montage EGW pour installer ton Vortex Viper/Venom, Burris FastFire ou Docter.
Tu peux retirer le montage et remettre ton viseur arrière à tout moment. Le matériel de montage est inclus, mais une légère modification peut être nécessaire pour les modèles Rock Island. Les produits EGW doivent être installés et vérifiés par un armurier qualifié.
Instructions d'installation
- Retire le viseur arrière*
- Installe le montage EGW dans la queue d'aronde
- Serre la vis de réglage (si applicable)
- Place le viseur point rouge sur le montage EGW (mettre un petit morceau de papier entre le viseur et le montage facilitera le retrait et évitera que le Loctite ne colle au viseur).
- Applique du Loctite bleu sur les vis de montage fournies
- Serre les vis de montage à 15in/lbs
Vis fournies :
- 2 vis à tête bombée - Fournies pour les viseurs Vortex Viper et Venom
- 2 vis à tête plate - Fournies pour les viseurs Burris FastFire et Docter
Les vis incluses avec ce montage nécessitent une clé Allen de 5/64'' pour l'installation. La modification de ton arme peut annuler la garantie du fabricant. Ce produit doit être installé et vérifié par un armurier qualifié. Aucune responsabilité n'est exprimée ou implicite pour les dommages ou blessures pouvant résulter d'une installation ou d'une utilisation incorrecte de ce produit.
Compatibilité
Ce montage est compatible avec (y compris, mais sans s'y limiter) :
- Sig Sauer 1911 Stainless Super Target*
- Sig Sauer 1911 Match Elite*
- Sig Sauer 1911 Target Full Size*
- Sig Sauer 1911 Max Full Size*
- STI avec viseurs arrière réglables
- STI Trojan
- STI DVC 3 Gun
- STI DVC Limited
- STI DVC Classic
- Springfield Range Officer
- Springfield Range Officer Elite Target
- Springfield Loaded Target
- Rock Island TCM Rock Target FS HC Combo 22TCM / 9MM
- Rock Island Pro Match Ultra 5” - 45 ACP
- Rock Island Pro Match Tac Ultra 6” - 45 ACP
- Rock Island Pro Match Ultra HC - 40S&W
- Rock Island Pro Match Ultra 6” - 10MM
- Rock Island Pro Match Ultra 6” HC - 10MM
- Iver Johnson Eagle XL-SS10
- Iver Johnson Eagle SS-10
- Iver Johnson Eagle O.D. Green
- Iver Johnson Eagle Coyote Tan
- Iver Johnson Eagle XL-10 Ported
- Iver Johnson Eagle XL-10
- Iver Johnson Eagle XL-45 Ported
- Iver Johnson Eagle XL-45acp
- Iver Johnson Eagle LR
EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Minor modification may be neccessary for Rock Islands. EGW products should be installed and checked by a qualified and competent gunsmith. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. This mount fits (including but not limited to): Sig Sauer 1911 Stainless Super Target* Sig Sauer 1911 Match Elite* Sig Sauer 1911 Target Full Size* Sig Sauer 1911 Max Full Size* STI with adjustable rear sights STI Trojan STI DVC 3 Gun STI DVC Limited STI DVC Classic Springfield Range Officer Springfield Range Officer Elite Target Springfield Loaded Target Rock Island TCM Rock Target FS HC Combo 22TCM / 9MM Rock Island Pro Match ULtra 5” - 45 ACP Rock Island Pro Match Tac Ultra 6” - 45 ACP Rock Island Pro Match Ultra HC - 40S&W Rock Island Pro Match Ultra 6” - 10MM Rock Island Pro Match ULtra 6” HC - 10MM Iver Johnson Eagle XL-SS10 Iver Johnson Eagle SS-10 Iver Johnson Eagle O.D. Green Iver Johnson Eagle Coyote Tan Iver Johnson Eagle XL-10 Ported Iver Johnson Eagle XL-10 Iver Johnson Eagle XL-45 Ported Iver Johnson Eagle XL-45acp Iver Johnson Eagle LR